ICOM IC 9100 TRANSCEIVER HF VHF UHF BASE 50MHz
As well as being able to be used in a wide range of frequencies, allows different modes of operation, not possible with other devices.
In fact, in addition to regular communications, RTTY emission are possible, D-STAR DV, via satellite or via luna (EME).
Received, includes a double conversion with a high image rejection mixer and consequently low intermodulation distortion.
In addition to the DSP technology in the stadiums of medium frequency digital feature allows all those very effective to counter the QRM and QRN regardless of bandwidth.
Independent dual multiband receivers and
The IC-9100 delivers well 100W HF 50 MHz on all 144 MHz,; 75W about 430 MHz and 1200 MHz 10W on, for the latter band is necessary the optional UX-9100.
The IC-9100 receive simultaneously two different bands: HF/50 MHz VHF + UHF + VHF/UHF, and 430 + 1200MHz.
For example, you can make a QSO on 7 MHz in the traditional way and, at the same time, prepare a connection through D-STAR Repeater in the VHF/UHF bands while observing in-band signals on presentation Overview pertaining to 7 MHz.
Double conversion receiver employing the 32-bit DSP.
In both HF and VHF/UHF up to 440 MHz, each band of main and secondary receiver has a dedicated DSP filters IF stadiums as well as constant predisponibili nimbly AGC selectable, dual PBT, manual or automatic attenuation peaks, noise reduction and noise suppressor.
First optional conversion filters on HF and 50 MHz.
In addition to the value of 15 kHz, already installed, there is the use of two other optional filters 3 kHz respectively (FL-431) and 6 kHz (FL-430).
3 kHz filter is especially recommended for the CW and SSB so as to eliminate overload phenomena produced by adjacent strong signals.
D-STAR * DV mode (optional)
This can be considered as the first application of the D-STAR * in a EPROM apparatus for HF. Adding the form UT-121 you will have access to this mode of communication.
How DV is applicable on 28 and 50 MHz simplex mode with its new applications as well as in traditional VHF and UHF bands.
DR mode then you can access to various repeaters with backbones attached.
USB connector for PC control.
To this port are transferable the modulation, demodulation and audio RX, RTTY DV. Using an appropriate software you can control and operate in various digital modes using the USB connection.
Via the CI-V data format the apparatus can be controlled with a PC.
The control is also possible using the command-level converter CT-17.
Their coordinates via GPS.
A special key GPS was installed on the front panel. By installing the optional dedicated UT-121 you can connect an external GPS receiver Data 1.
Data relevant to the position, as well as in automatic mode can also be set manually. Its coordinates are shown on the display and can be sent to other stations by the way DV.
Receiving GPS data transmitted from another station will yield relevant data the direction and distance from the callers.
Operating mode via satellite.
In satellite mode you can achieve synchronization between the increments of harmony between ' uplink (transmit), those ' downlink ' (reception).
20 alphanumeric memories for this mode of communication allow you to store the frequency, the operating mode and audio tones to get a quick arrangement.
Optional programming software CS-9100.
Using a PC and USB connecting cable, using such software you can access the various alphanumeric memories, names, characteristics of filters and settings on AGC. It follows a simplification on the communication of the characteristics used to another correspondent to test your settings.
Demodulator and decoder RTTY.
Their presence allows to obtain immediate signal decoding RTTY received.
It is not required to use any external PC.
Optional UX-9100 for 1.2 GHz band.
1200 MHz band is accessible via the insertion of the required form. Will be possible even satellite communications through the ways L/V or L/U.
- Antenna tuner for HF and 50 MHz.
- Issuance of a tone audio bandwidth limits.
- Speech synthesizer relevant operating frequency, mode and level of the received signal (S meter).
- Jack for electronic manipulator on the front panel.
- Four dedicated memories electronic CW Manipulator.
- Function of Voice Squelch Control.
- Multifunctional Indication to the level of the received signal, the level of output power, the ROS, the ALC and level of compression.
- Connectors for external speakers main and auxiliary receptor.
420,000 ~ 480,000 MHz *
1,240,000 ~ 13,200,000 MHz **
3,500 ~ 3,800 MHz
7,000 ~ 7,200 MHz
10,100 ~ 10,150 MHz
14,350 14,000 ~ MHz
18,068 ~ 18,168 MHz
21,000 ~ 21,450 MHz
24,890 ~ 24,990 MHz
28,000 ~ 29,700 MHz
50,000 ~ 52,000 MHz
144,000 ~ 146,000 MHz
430,000 ~ 440,000 MHz
1,240,000 ~ 1,300,000 MHz * ** Some frequency bands are not guaranteed
** Using the optional UX-9100
DV (with UT-121 optional)
call 3 (channel 1 for each band)
18 (6 channels for each band)
20 for satellite
26 for GPS
SSB, CW, RTTY, FM, DV AM HF/50 MHz: 2 ~ 100W 2 ~ 25W 144MHz: 2 ~ 100W - 430/440MHz: 2 ~ 75W -
(28-29.7) 0.40 microvolts 0.18 MV DV - 1.26 µV
0.79 µV 0.35 MV SSB/CW, AM: 10dB S/N
FM: 12dB SINAD
DV: 1% BER
Preamp1 ON: 0.5-1.8/1.8-29.9 MHz
Preamp2 ON: 50-54MHz
(BW = 2.4 kHz) 2.4 kHz/-6 DB; 3.8 kHz/-60dB CW:
(BW = 500Hz) 500Hz/-6dB; 900Hz/-60dB RTTY:
(BW = 360) 360/-6 DB; 650Hz/-60dB AM:
(BW = 6kHz) 6.0 kHz/-6 DB; 15 kHz/-60dB FM:
(BW = 15 kHz) 12.0 kHz/-6 DB; 20 kHz/-60dB DV:
(12.5 kHz spacing) >-50dB
All the radios contributed by cover normally only the amateur bands.
The extension a frequency radio (TX-RX) it is made out of express request reviews. The transceivers radio amateurs are usually not indicated for use outside of the amateur bands.In some cases, the radio and especially the amplifier final or output filters can be damaged during transmission to out of gangs amateurs.Such damages not are covered by no guarantee. La manufacturer warranty is cancelledas a result of the extension of frequency.